wag swag

DIY Step in Dog Harness Tutorial

DIY Step in Dog Harness
Materials needed:
2 yards of nylon webbing
2 yards of coordinating ribbon (jacquard or grosgrain work best, and this is OPTIONAL)
Hardware:
Note: You NEED to customize the hardware to the size of nylon webbing you are using! IF you use 1” webbing, you need to get 1” hardware. The most common sizes for webbing and hardware are: ½”, 5/8”, ¾”, and 1”. 1 ½” is also available for larger dogs and can be found fairly easily, but remember that the larger the size, the more it weighs. For strength purposes, I recommend metal WELDED hardware.
1 side release buckle
2 D ringsblog supplies harness
2 round rings
2-3 tri-glide slides
Additional items needed:
Scissors
Lighter
Measuring tape or grid
Sewing machine and matching thread or matching bobbin thread and clear thread for the top.

PLEASE excuse the bruise on my finger.  I smashed it in the door after successfully using a hammer ALL DAY LONG with no problems.  GEEZ…

Now we are ready to begin. You need to first choose a size. At the end of the tutorial, I will make a list of the sizes you will need to cut the pieces. You will need to decide the size you are going to make, and cut the webbing accordingly.

First, IF you plan to put any type of ribbon on your webbing, sew that on first. THEN cut the webbing to the sizes you are going to need. Use the lighter to secure the ends by LIGHTLY melting the webbing so it will not fray. NOTE that I said LIGHTLY. I don’t want any burnt fingers and/or houses.

You will be cutting 1 bottom piece, 2 side pieces, and 2 top pieces.

The tri-glide slide on the bottom piece is OPTIONAL. I don’t like it, because it creates a lot of extra bulk that I don’t feel is necessary. Besides, when out on a walk with my dog, I want her to be able to lay down a bit. Laying ON the additional slide doesn’t look comfortable.
Start by taking the bottom piece and sewing the end back on itself. IMPORTANT!! Make sure you leave enough of a gap to thread your side pieces through it! . I like to use a zig zag stitch to make sure it is nice and secure. I sometimes put 2 rows, and allow one row to overlap the edge to give it additional protecting from fraying. Do this every time you are sewing on an “end”.

blog harness step 1.1

Next loop your side pieces around a tri-glide slide and sew them down.

blog harness step 2

Here comes the tricky part! Take ONE of the O rings, and slide the end of your side pieces that does not have the tri-glide slide on it through the O ring. Come from what you will designate as the INSIDE of the O ring.
Then loop your end around the O ring and go up, through, and over the tri-glide slide. (Step 1)
Now take your bottom piece and thread the free end through that. (Step 2)
And DON’T FORGET to put the first piece we made through the free end before threading it through the next O ring. (Step 3)
Repeat with the other side (Step 4.)

blog harness 4 steps for making middle

Next, take the second O ring, and coming from what you will designate as the OUTSIDE of the O ring, loop the side pieces through the O ring and secure it with the zig zag stitching. It is starting to look like a harness!

blog harness second o rint

Next, take your two top pieces and your 2 D rings and your side release buckle. Loop your top pieces through the O rings, and secure with zig zag stitches. Make sure that your design, if you have one, is facing OUT!

blog harness top attachents

Then take your D ring and slide it on one of the top pieces. Secure it at the top with your zig zag stitches, leaving room at the bottom for your side release buckle. ALMOST DONE! Repeat for the other side.

blog harness top finish attachments

Lastly, put the side release buckle on the webbing and secure it. Make sure that the buckle parts are facing the correct direction!!! Repeat with the other side.

blog harness top finishing stitch

TA DA!!!! You have a harness and you did it ALL BY YOURSELF!

blog harness 2 views

blog dj in harness

DJ wearing harness for blog

For a printable version, click the link below!

DIY Step in Dog Harness

Sizing chart:

DJ is wearing an XXS, for dogs 4 pounds and under.  (He weighs 4 pounds, and it is fully extended.  These measurements are just a guideline.  For best results, measure your dog and put the measurements you come up with in the middle.  These numbers are what you cut the webbing to be, NOT the finished size.  Fold overs are approximately 1″ each.

Size       Top *cut 2            Sides *cut 2              Bottom piece                  Hardware
XXS            5”                         12”                             5 1/2”                             ½”
XS              6”                          20”                               7”                            ½” or 5/8”
S                 7”                          27”                               8”                                  ¾”
M                8”                         33”                               9 ½”                          ¾” or 1”
L                 8”                         40”                               11”                                  1”
XL              9”                         45”                               13”                               1” or 1 ½”
If you DON’T want to do it by yourself, drop me a message, email me, or stop by my Etsy store wagswagpetsupplies to get one that I made for you! 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s